Image 1 of 4
Image 2 of 4
Image 3 of 4
Image 4 of 4
DISCLAIMER NOTICE: Amron's chamber lights are designed to be used in air chambers where oxygen concentrations remain below 23.5%. Our lighting products are NOT designed for oxygen service, are not intrinsically safe, and do not meet the criteria given in NFPA-99, Chapter 20 and other applicable definitions. Misuse of our chamber lighting products in high-concentration Oxygen environments may result in serious injury and/or death.
The Amron International model 7100 LED Hyperbaric Chamber Light provides industry leading chamber illumination with a compact, low-profile design, an integrated touch switch dimmer feature, and flexible mounting options.
The 7100 LED light comes with an industry standard mounting plate to allow easy mounting in existing chamber installations. The mounting plate is designed so it can be removed and rotated. This allows locating the connector or switch to whatever orientation is convenient for the chamber installation. The 7100 can also be used with an optional magnetic base that allows for quickly moving the light to wherever its needed, in whatever orientation is desired.
The LED light has a maximum brightness of 1000 lumens of bright white (5000K) light. The touch switch allows the user to select from 6 different brightness levels with the touch of a finger. The borosilicate glass lens is frosted to provide diffuse lighting. Optional red or blue lens filters are also available.
The 7100 dimmer function is controlled by a touch switch located on the side of the light. When the 7100 LED light is initially powered up, it is automatically at level 2 brightness. The dimmer control touch switch works by increasing the light level with each touch until the maximum level is reached. After reaching maximum brightness, each successive touch will reduce the light level until the light is off. Continuously touching the touch switch has no effect. Should the light be turned off inside the chamber, the chamber operator can turn the light back on by cycling the power to the light from the outside.
The 7100 comes with an industry standard 3-pin bulkhead connector similar to an RMG-3-MP Marsh Marine connector that mates with an optional RMG-3-FS connector / cable. Should your installation require a low smoke, zero halogen cable, the optional WPC-3-FS-10 connector / cable is also compatible with the 7100 connector. Locking sleeves are also available optionally in two different materials – Delrin (G-FLS-D) and Stainless Steel (G-FLS-S).
For an LED hyperbaric chamber light that has all of the features of Amron’s model 7100 light, but which can also be controlled remotely from outside the chamber, see Amron’s model 7120 LED light.
Frequently Asked Questions
-
Yes. Please refer to your user manual for instructions.
-
Yes, but the light has not been third party tested and it does not come with any third party documentation.
-
The 7100 Series Hyperbaric Chamber Light and a 3- or 4- power cable with locking sleeve which is not included with the chamber light. Amron recommends the RMG-3-FS for the model 7100 Hyperbaric Chamber Light and the RMG-4-FS for the 7120 Hyperbaric Chamber Light. The standard RMG connector comes with an 18 inch pigtail but custom lengths are available. Also note, the standard RMG connector does not come standard with low smoke zero halogen cable, if you require this type of cable please let your sales representative know prior to placing your order. You will need a 4 conductor 18 AWG electrical penetrator to pass your power supply through the pressure boundary. When using the 7120 Hyperbaric Chamber Light with dimmer option, Amron recommends using a 0-10V dimmer controller. When using the 7100 Hyperbaric Chamber Light, Amron recommends using a standard household On/Off Switch. Both switches can be purchased at most hardware stores.
-
Yes, there are 8 screws under the integrated mounting plate that can be removed to allow you to reposition the housing on the mounting plate.
-
No
-
The 7100 Series Hyperbaric Chamber Light has a unique pressure vent that allows gas to pass in and out of the light housing.
-
No, you will need to purchase a standard 3 or 4 pin RMG Waterproof connector. The 7100 series requires a three pin connector where the 7120 requires a 4 pin waterproof connector. You should also purchase the female locking sleeve to protect your waterproof connector from accidental disconnection.